An Easy Plumbing Guide for Installing a Bathtub
An Easy Plumbing Guide for Installing a Bathtub
Blog Article
How do you really feel in regards to How to Install a Bathtub?
Mounting a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult task. If the old bathtub is readily easily accessible, the project can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit attempting it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider employing one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This article will certainly help you set up a new tub in your washroom if you have actually currently bought a brand-new bathtub and do not need to transform the arrangement of your previous water system pipes.
Your tools and also product checklist ought to comprise the following:
Preparing for the Installation
Firstly, the supporting frame provided with the bath needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make certain that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last setting.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The process of getting rid of the existing faucets can be rather problematic because of the limited gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, position the tub in the needed position. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the supply of water and inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally examine the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait till the bathtub has actually been utilized a minimum of when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the supplier provided backnut. When the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former kind needs to be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split an inflexible seal, creating the water to permeate the wall between the bathroom as well as the tiling, causing issues with moisture and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, as well as can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to enable the motion experienced when the tub remains in use. The sealant can split relatively very early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very eager about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed our page. So long as you enjoyed our page plz make sure you remember to share it. Kudos for your time. Visit us again soon.
Call Us Today Report this page